What's in the Box:
- 1 x VPC VMAX Prime Throttle
- 3 х Button Inlay Sheets
- 1 x USB Cable 2 m.
- 1 х Detent Plate Aerobatics Set (preinstalled)
- 1 х Detent Plate Classic+ Set
- 1 х Detent Plate Warthog Set
- 1 х Detent Plate CosmoSim Set
- 2 х Button Module
- 1 х 4-way Hat
- 4 х M5x10 Screw
Axis Adjustment
Tools required:
- H3 Hex Key (NOT INCLUDED)
To adjust the clutch damper force use a H3 Hex Key. Tightening the bolt will increase the effect of the clutch damper, loosening the bolt will reduce the effect. Each axis can be adjusted independently by tightening or loosening each clutch damper.
Installing Detents
Tools required:
- H2.5 Hex hey (NOT INCLUDED)
To replace the detents, remove the marked screws, adjust the position of the preferred detents and tighten the screws.
To lock the finger lifts in the upper position, hook the hinges into the highlighted screws.
Module replacement
Tools required:
- Phillips Screwdriver (NOT INCLUDED)
Remove the highlighted screws and replace the modules with the preferred ones.
Important! The upper hat module can be installed in its place only.
![](https://s3.amazonaws.com/cdn.freshdesk.com/data/helpdesk/attachments/production/47299602462/original/9iZcfPB1Gvj0MBwOhRijpZFDm0pgBak05w.JPG?1720157437)
Cap replacement
![](https://s3.amazonaws.com/cdn.freshdesk.com/data/helpdesk/attachments/production/47299603005/original/qNORlU5s8EFCpXcJ-GdBGlrNL1b_PRIsAA.JPG?1720157826)
![](https://s3.amazonaws.com/cdn.freshdesk.com/data/helpdesk/attachments/production/47299603054/original/u8BfywBL-NvFHA3axeXDhMgztEXmvaSYnA.JPG?1720157865)
![](https://s3.amazonaws.com/cdn.freshdesk.com/data/helpdesk/attachments/production/47299603086/original/dCNIPyxW7LBxzOa6dTXlKnHSqldmfPyL5g.jpg?1720157906)
Mounting to the VPC Desk Mount
Tools required:
- H2.5 Hex hey (NOT INCLUDED)
- H4 Hex hey (NOT INCLUDED)
![](https://s3.amazonaws.com/cdn.freshdesk.com/data/helpdesk/attachments/production/47299630166/original/EP7eiXSU8an0BEV_DZVNUsP3N_ETI_kFYQ.png?1720167924)
1. Remove the highlighted screws and detach the legs.
![](https://s3.amazonaws.com/cdn.freshdesk.com/data/helpdesk/attachments/production/47299630164/original/VAUV14ULGT8i_Hh5jexUUF1D9I9_2MYwCg.png?1720167923)
2. Place the throttle on the bracket and insert M5x10 screws, adjust the position of the unit and tighten the screws.
![](https://s3.amazonaws.com/cdn.freshdesk.com/data/helpdesk/attachments/production/47299630167/original/q2jfli6lpCVMzRavPxPFaFizcMWXXym1bA.png?1720167923)
Device Connection
![](https://s3.amazonaws.com/cdn.freshdesk.com/data/helpdesk/attachments/production/47299603086/original/dCNIPyxW7LBxzOa6dTXlKnHSqldmfPyL5g.jpg?1720157906)
Mounting to the VPC Desk Mount
Tools required:
- H2.5 Hex hey (NOT INCLUDED)
- H4 Hex hey (NOT INCLUDED)
1. Remove the highlighted screws and detach the legs.
2. Place the throttle on the bracket and insert M5x10 screws, adjust the position of the unit and tighten the screws.
Inserting Button Inlays![](https://s3.amazonaws.com/cdn.freshdesk.com/data/helpdesk/attachments/production/47299598880/original/NE7ncc_v--gDAhJG56qg_PHzf_goL2r_cw.png?1720153682)
Troubleshooting
Please visit the VIRPIL Controls support portal for troubleshooting advice. If you are still experiencing issues or unable to find answers to your specific question, please create a ticket on our support portal!
https://support.virpil.com
Was this article helpful?
That’s Great!
Thank you for your feedback
Sorry! We couldn't be helpful
Thank you for your feedback
Feedback sent
We appreciate your effort and will try to fix the article