Chair Mount - Collective Base - User Manual

Modified on Tue, 7 Nov, 2023 at 12:01 PM

What's in the Box:

  • 1 x Mounting Plate


  • 1 x Mounting Plate (Front)


  • 1 x Mounting Plate (Rear)

  • 10 x Cable Clips

  • 4 x Spacer

  • 4 x Bolt DIN 912 M8x50 А2
  • 4 x Washer DIN 127 8 A2 
  • 4 x Washer DIN 9021 8,4 A2

  • 4 x Bolt DIN 912 M6x45 А2
  • 4 x Washer DIN 127 6 A2 
  • 4 x Washer DIN 9021 6,4 A2

  • 8 x Screw ISO 8677 5х16 А2
  • 8 x Washer DIN 9021 5,3 А2 
  • 8 x Washer DIN 127 5 А2 
  • 8 x Nut DIN 934 M5 A2





VPC Chair Mount Configuration Options


Recommended Installation for VPC Rotor TCS Base

Example Chair #1


Tools required:

  • 8 мм Wrench (NOT INCLUDED)
  • H5 Hex Key (NOT INCLUDED)

1. Unscrew the highlighted screws from the base plate of the chair

2. Using the existing holes, secure the front and rear mounting plates with the lip facing downwards, as shown in the figure below. Use the DIN 912 M6 screws and spacers to attach the plates.

IMPORTANT: if the shape of the chair base plate does not allow installing the mounting plates from the outside, then you should install them between the plate and the bottom of the seat.



3. Place the bracket in a suitable position and secure the front edge with the supplied screws and nuts as shown in the picture.

4. Determine the desired distance of the VPC Rotor TCS Base from the seat using the additional holes in the corner of the base and secure using the remaining screws and nuts.

5. Insert the clips until they click into place and route the cable through them.


Alternative Installation for VPC Rotor TCS Base

Example Chair #2


Tools required:

  • 8 мм Wrench (NOT INCLUDED)
  • H5 Hex Key (NOT INCLUDED)

1Unscrew the highlighted screws from the base plate of your chair.

2. Using the existing holes, secure the front and rear mounting plates with the lip facing upwards, as shown in the figure below. Use the DIN 912 M6 screws and spacers to attach the plates.

3. Place the bracket in a suitable position and secure the front edge with the supplied screws and nuts as shown in the picture.

4Remove the VPC Rotor TCS Bracket and reattach it after rotating it 180 degrees.

5Determine the desired distance of the VPC Rotor TCS Base from the seat using the additional holes in the corner of the base and secure using the remaining screws and nuts.



Recommended Installation for VPC Rotor TCS Base

(Example Chair #3)




1Unscrew the highlighted screws from the base plate of your chair.

2. Using the existing holes, secure the front and rear mounting plates with the lip facing upwards inside the chair frame, as shown in the figure below. Use the DIN 912 M6 screws and spacers to attach the plates.

3. Place the bracket in a suitable position and secure the front edge with the supplied screws and nuts as shown in the picture.

4Remove the VPC Rotor TCS Bracket and reattach it after rotating it 180 degrees.

5Determine the desired distance of the VPC Rotor TCS Base from the seat using the additional holes in the corner of the base and secure using the remaining screws and nuts.


Troubleshooting


Please visit the VIRPIL Controls support portal for troubleshooting advice. If you are still experiencing issues or unable to find answers to your specific question, please create a ticket on our support portal!


https://support.virpil.com


Was this article helpful?

That’s Great!

Thank you for your feedback

Sorry! We couldn't be helpful

Thank you for your feedback

Let us know how can we improve this article!

Select at least one of the reasons
CAPTCHA verification is required.

Feedback sent

We appreciate your effort and will try to fix the article